Follow on WordPress.com

How To Get The Bearings Out Of Skateboard Wheels

When the wheels do not turn as smoothly as before, the cause may lie in the bearings. Bearings are usually round pieces made of metal that people hold inside the wheels to mount the wheels to the axle. In fact, wheel bearings play a significant role in helping the board to move quickly and smoothly. Therefore, everyone should take care of the camps often.

Removing old skateboard bearings is relatively easy. Unfortunately, if you don’t know how to do it, it can be quite complicated. Therefore, this article fully meets your needs at the moment. Sit down and keep reading for more information.

The best bearings for long boards

Tools

To remove the bearings from the skateboard wheels, it is crucial to prepare some of the following tools, such as:

  • Screwdriver
  • Wrench
  • Bearing thrust device
  • Skateboard tool
  • Leverage
  • Other important things like a towel, liquid, etc.

How to remove the bearings from the skateboard wheels

1

Unscrew the wheels from the axle

Unscrew the nut holding the axle wheel

Unscrew the nut holding the wheel

There is a nut on the axle that holds the wheels. What you need to do is make an effort to unscrew the nuts lying at the end of the shaft. In this case, it is recommended to use a skateboard or wrench tool to get the highest efficiency.

Depending on the specific situation, you can remove all the nuts or just a nut. For example, if you want to replace all bearings, you must remove all four-wheel nuts. On the contrary, if you are almost certain that you will find out where the problem is, you only need to remove these nuts on the wheels.

However, you need to determine if your skateboard has certain types of support shields or not to remove them as well. Also, if there are spacers in your wheels, be sure to lose them when removing and placing the wheels back on the skateboard.

Push the wheel all the way to the axle

Push the wheel all the way to the axle

In this step, the bearings must be removed from the wheel. The most common way people apply is to use the truck’s axle. For this reason, you must slide the wheel towards the end of the axle. This means that the truck axle must enter as long as the bearing is still on the axle.

In addition, if your skateboard tool has a pull-out bearing, you can use it to remove the bearings instead of the shaft. Of course, you have to remove the wheel from the axle completely.

Another thing to notice is that there are a few washers between the axle that you can’t lose.

Lift the bearing off the skateboard truck

Lift the bearing off the skateboard

It is ideal to use a lever that helps you remove the wheel from the skateboard. All you have to do is use your palm to grab the wheel. In particular, the heel of your hand will be placed on the lower edge of the outside of the wheel and your fingers will be at the top of the wheel.

The next step is to use the lever slowly and carefully to pull the bearing off the wheel in one direction. In this case, a down angle is recommended. In principle, the bearing should pop out of the wheel, but may not come out completely. This way, point it in another direction until it comes out. This process is the same as the way you take the lid of a glass bottle.

This process requires care as well as slowness. If you want to replace new bearings, it is good to break the old ones. On the contrary, if you don’t want to throw away these skateboard bearings and just clean them, be as careful as you can.

Also, while using a pull-out bearing to easily remove the bearing from the wheel, let’s place the tip in the bearing so that it can hook the edge of the bearing.

Remove the other bearing from the same wheel

Remove the other bearing

If you have removed one bearing once, it is more convenient to repeat this process for the other side. Let’s put the tip of the shaft of the bar in the second bearing after turning the wheel. In this step, it is easy to remove the bearing, as the wheel is visible inside. As a result, you can judge the extent to which the shaft or tool enters. Of course, it is crucial to leave enough space for the axle so that it does not hit the inside of the wheel.

2

Clean the skateboard wheel bearings

Clean the skateboard wheel bearingsWhile you notice that your bearings look dirty or make a serious noise when you turn the wheels, now is the time to clean the bearings on the skateboard. Make sure you do this quite often to increase the life of your camps.

Clean dirt and deposits from the bearings

Use a paper towel or an old rag to wipe dust from the bearings. If there are any visible debris on the camp, remove it immediately. You must clean the bearings completely at the front and rear to prevent dust from escaping. Quick cleaning is enough for those bearings that do not have a big problem.

Switch off the rubber fuses

Remove the rubber fusesThis step of removing the fuses requires something sharp like a small screwdriver, razor or paper clip. Choose one of these things to slide it under the rubber shield. Make sure you are careful while diverting it. If you are not careful, the rubber fuse may be cut or more serious, the rest of the bearing is damaged. In this case, I guess the razor is more suitable than a paper clip.

In fact, the fuse should not be removed. However, it is essential when cleaning the bearing as thoroughly as possible. Also, keep in mind that some special bearings have more than a fuse. Therefore, check carefully and remove all before proceeding with cleaning.

Soak the bearings in a bearing-specific solvent

Soak the bearings in a bearing-specific solventYou need to prepare a camp-specific solvent that many local skate shops offer. You can also consult some liquids, including acetone, pure alcohol, carburetor cleaner, or even lemon juice, which replace the cleaning solvent. Then place the bearings in a glass jar filled with liquid. The time we soak the bearings depends on how dirty they are. Ten minutes is usually perfect.

However, the new bearings will be worth your investment if the old ones are incredibly rusty. Rusty bearings cannot work as efficiently as before, just by cleaning and lubricating. Cleaning and lubricating the bearings actually helps them work again, but does not guarantee their good condition.

Rotate the bearings around in the jar

After about 10 minutes of soaking the bearings, you can shake them around the jar for a minute. This action allows you to remove additional debris or accumulations in the bearings. A one-minute spin helps to complete the cleaning.

Remove the bearings from the jar and dry them

Remove the bearings from the jarAfter the cleaning process, it is now ideal for removing the bearings from the jar. Then you need to put them on a towel to let them dry. It is better to use a towel to wipe the wet bearings in turn so that it can be as dry as possible. It is better to dry all sides by moving the balls in the track or using a hair dryer or fan. As a result, all the moisture in your bearings will evaporate completely.

Spray or wipe the bearings with grease

Spray or wipe the bearings with greaseIt is advisable to lubricate the bearing balls before placing them again. The reason is that lubrication helps the bearings to work more efficiently. Cleaning is actually not enough. Therefore, let’s take a few drops of lubricant, buying from a skate shop. Another choice you can consult is the use of motor oil or quick cream, which most barbers use on their electric razors. One notable thing is that the WD40 is not recommended in this case, as it can cause the bearings to dry out and crack.

Replace the rubber shield and replace the wheel bearings

Release the rubber shield backThe last step you need to do is put all the guards back on. Then you need to put all the clean bearings back on the wheels. Two bearings will be placed on both sides of the wheel and a total of eight bearings.

zeato skate tool

Zeato Skate Tool-Amazon Best Seller-Buy Here on Amazon

Summarizing

No matter how expensive your product is, it can wear out after being overused and subjected to excessive pressure for a long time. For this reason, it is better to pay attention to the careful and frequent maintenance of cleaning, so that the performance of your bearings becomes better.

We hope that this article helps you a lot in removing the bearings from the skateboard wheels and cleaning them yourself. If you find it a useful guide, share it with your friend.

Leave a Reply

Your email address will not be published. Required fields are marked *

Follow on WordPress.com