Follow on WordPress.com

How to fix a broken skateboard

Have you broken your skateboard or most of its layers? Learn how to fix that deck so you can ride it again.

Did your favorite board break in two? Yes, it can be frustrating, but it’s all part of the game. All parts of the skateboard have the potential to break. The wooden deck is the one most likely to break.

New skateboards cost 35 to 300 dollars.

Depending on your initial investment, you may want to extend the life of the broken board.

Most skateboards break in the middle, halfway between the trucks. There’s a reason why that happens. “Whenever you get on board, you put an incredible load on it,” said Peer Welder and Peter Whitley, authors of Mastering the Skateboard.

“Although skateboards can get damaged in multiple ways, there are certain places on a board where you can land, which will dramatically increase its chances of breaking or cracking.”

Therefore, the tricks should end with a clean, confident landing whenever possible. If you want this to happen, you have to be on the board as much as possible.

The area on the trucks and wheels is the strongest zone when landing a trick due to the transfer of all downward force.

“The worst place to land is with one foot on either the nose or the tail and the other foot between the trucks,” Welder and Whitley added.

The following three methods can be applied if your skateboard is cracked in half.

Instead of destroying it, repair it and use it to skate.

The board can never be as strong or hard as the original, so it will become weaker over time, but it can still be ridden a little while longer.

1. Duct tape

The fastest and weakest way to fix a broken skateboard is to fix it with duct tape.

The problem is that you will have to cover the broken parts and then wrap the tape around the good parts of the skateboard.

The result is a smaller and slightly uneven skateboard, which will probably only be useful for riding without doing any tricks.

Using duct tape to repair and repair a broken skateboard is the cheapest solution available.

You can also try using tape-based products that mix industrial-grade fibers and specialized resin to glue and harden your damaged skate.

Carbon fiber tape: a temporary solution for broken skateboards

2. Rails

One option is to install railings on the deck.

All you need to do is screw the rails into the board to hold the broken parts in place.

Although rails are no longer in vogue, they can make your board really stiff, especially if your skates are only partly broken.

Rails will also provide you with good pop.

3. Additional layer of wood

If the skateboard is already broken but you have another deck or another flat piece of wood, then you can try to join the separate parts.

First, measure the board’s width.

Create a rectangular piece of wood that runs across the deck and generously extends over the broken portions of the board.

Glue it to the bottom of the board, then screw it with flat screws from top to bottom.

The fixed skateboard will slide perfectly and will even allow you to land a few tricks.

The drawback is that you’ll have extra wood under the board, so obstacles and ledges will be harder to grind on.

No matter how strong the skateboard gets, it won’t be great.

There are a few things to keep you from breaking your board. Some are  trade-offs in what you will skate but they keep you rolling longer.

  • Don’t do lipslides very much. The motion of landing on the rail can cause lots of breaks and snaps.
  • Don’t do big drops or stairs. The higher the drop the more likely you are to break your board.
  • Bailing out on tricks sometimes to save from a snapped deck. Even if I could have landed the trick. Would you rather miss a few extra times then smash through a good board.

Final tips for damaged or broken decks

If your skateboard isn’t exactly broken in half in two pieces, consider repairing it to make it last longer.

Remove any grip tape that is affixed to the deck, clean the deck thoroughly, and apply epoxy to close any cracks.

After a 24 hours drying period, the surface should be smoothed by using fine sandpaper and a new grip tape should be inserted.

Finally, if your board is warped, remove the wheels and trucks and immerse the board in water for 12 hours.

Immediately after this, place the deck on an even surface and place a heavy object on top. You should wait 24 hours prior to assembling your skateboard and resuming riding.

Wet wood is pliable, so this technique will help it return to its original shape.

Leave a Reply

Your email address will not be published. Required fields are marked *

Follow on WordPress.com